1966 BSA 650 Cafe Lightning Spitfire

The bike was built in the old school caf? style with a lot of power and torque. Bike starts easily and runs great with a very strong engine.

I bought the bike from the builders as an addition to my collection but now I need to make room for other items.

The original builders of this bike were extremely meticulous with the build process building it from the bare frame up; media blasted the frame and painted it with a base coat clear coat application. All parts of the bike were assembled with great care.

Frame Number: A65L-5041 Frame Number indicates it is a 1966 Lightning

Engine Number: A65S-8117 Engine Number indicates it is a 1966 Spitfire

Title: Clear Arizona Title in my name

Here is a list of the many new parts that went into the build of this bike not including all those small odds and ends:

*Crank Shaft Bearing & Bushing

*.40 over 10.5 Made in England

Spitfire Pistons

*Piston Rings Made in England

* Valve Guides

*Rowe Valves

*Fuel Lines

*Gaskets & Seals – ALL

*Primary Chain

*Pazon Ignition

*New Lucas 6 Volt Coils

*Plug Wires and Cap

*All Wiring

*Tympanium Regulator

*1.75 Header Pipes

*Cafe Mufflers

*Speedo & Tachometer

*Old Style British Headlight

*Miller Amp Gauge

*Tires and Tubes

*Chain

*Paint

*Caf? Bars

*Grips

*Kill and Horn Switch

*Brake Shoes

*Fork Seals and Seal Holders

*Sealed Battery

*Shift Lever

*Kick Shift Foot Peg Rubbers

*Barnett Cables (including

Speedo & Tach Cable)

Carb Jets & Gasket Kit along with new Amal slides

New Clutch with heavy duty Barnett Springs, cups and spring retaining nuts

Engine was built from the crank shaft sludge trap up. Cylinder was bored .40 over and matched to the British made pistons. The head was redone with new guides installed and seats cut to match the new valves. The machinist also installed crank shaft bushings and machined it to factory specs. Wiring was completely redone, ith all joints soldered, eat-shrink and run in cloth loom. The seat was professionally redone; foam is great and the seat looks beautiful.

Engine has proper 1966 Amal Mono Block carbs. Both carbs are in very nice shape. One is 389-228 and the other is 689-228 making these matching left and right carbs for 1966. All brass gaskets and seat needled are fresh along with slides.

Paint on frame is high gloss black, ase coat clear coat automotive paint. Tank and fender were also done in base coat clear coat in gray with light gray racing stripes. Tank and fenders were in very nice shape prior to painting.

Bike has big valve head, pitfire higher compression pistons. It also has the vintage Amal mono blocks with velocity stacks with the brass screens. So if you use it as a daily drive you may want to put regular filters on the bike. Bike has the center and side stand. The bike currently has new racing caf? bars installed.

This BSA has a quick disconnect rear wheel as well as a functioning choke lever on the handlebar. It still has Ewerts functioning fuel petcock with the cross over tube. The rims are original British made Jones Wheels. They are still nice but they are 40 + years old, o they do show some wear on the chrome. But as they are original I did not want to replace them with the cheaper light duty ones. They still look nice with some light patina on them.

This is one very nice British bike that is a blast to ride. The bike has 52 trouble free miles on it since restoration.

Winning bidder must contact me within 12 hours after close of auction with payment information and full payment must be received within 3 days of close of auction. Bank Wire Transfer is the preferred payment method.

International Bidders please do your research prior to bidding to determine what is required to get the bike into your country

Also published at eBay.com