Custom Harley Cafe Racer / Street Fighter Todd's Cycle Bull Sportster Buell moto

Description

 

This motorcycle. called "Bull" was built by Todd Silicato | Todd's Cycle (www. toddscycle. com) and has competed at; AMD Championship. Artistry in Iron during Las Vegas Bikefest. IMS Ultimate Builders Competition. featured at 'The One Show' in Portland. Oregon. Bull has been featured in countless magazines and websites and had a feature spread in Japan's Hardcore Chopper Magazine. Hot Bike Magazine and others.   This is a ground up. hand crafted custom caf?© / street fighter and you will absolutely NEVER see anything like it. From the monoshock rear suspension. single downtube frame (that acts as an oil tank). inverted front end with radial brake. hand formed aluminum bodywork. etc. Bull exemplifies the custom street fighter. Bull doesn't just look good. it handles like a sportbike should. primarily because the frame was setup to mimic the Suzuki GSXR1000 frame geometry and riding position.     I have been working with and friends with. Todd's Cycle for a decade. I acquired . Bull" about two years ago with no motor (a complete roller). I decided to bring Bull back to life so I did just that. I stuck a screamin fast 1999 Buell X1 1200cc motor in the custom frame. 2 tone gloss and flat back rocker boxes. brand new DYNA 2000i ignition. coils. Mikuni HSR42 carburetor and more.  The original color scheme was anodized aluminum bodywork but when I rebuilt Bull. I decided to paint the hand formed aluminum bodywork instead. I shipped the bodywork to Todd's Cycle and told Todd to paint it any way he wanted. in the end. it was his vision. The colors you see. laid on by Color Zone Designs in Huntington Beach. CA. are 100% the vision of Todd?ˆ™s original design.   The bike and all its components have less than 50 miles on everything except the motor (the motor is from a 1999 Buell X1 Lightning with 20K + miles and runs AMAZING!).  Everything listed below is new unless otherwise listed. Any wear on the bike is from a couple short test rides and moving around the shop. taking to shows. etc. Even the tires still have the rubber nipples on them!

VISIT WWW. BULLCAFE. WEEBLY. COM for more photos. details. build photos. etc.

SPECIFICATIONS BUILT | 2007 REBUILT | 2013 - motor  and paint TITLE | Clean. currently registered in the state of Washington. registered as a 1999 Buell to #s match the motor SPECIFIC CUSTOM DETAILS  Oil tank is at the neck of frame. plumbed through the downtube. Oil tank is hand made from aluminum and black anodized. plumbed with AN fittings. DRIVELINE 1999 Buell X1 Lightning 1200 V-Twin (evo sportster platform) 14K miles on the driveline Mikuni HSR42 with Todd's Cycle choke relocation kit  Todd's Cycle Air Cleaner  Shaved cam cover. LOVEJOY Rosta chain tensioner (documentation included). O-Ring chain. PBI offset drive sprocket. all AN fittings and braided oil lines. Exhaust is a hang made system that runs on both sides of the motor and snakes uo under the seat pan into a merge collector and then into a tunable Bassani canister (with integrated baffle). All exhaust is ceramic coated in a color similar to hard anodized gold.

SUSPENSION GSXR 1000 inverted front end with black nitrite fork sliders (gloss black) GSXR 1000 adjustable monoshock (custom coated) RSD / Roland Sands Designs prototype GSXR tripe trees (gloss black with bead blasted accents) FRAME Custom made "one-off" hand fabricated frame by Chassis Design Company (www. chassisdesigncompany. net) to Todd's specifications. custom built around a 1200cc Buell / Sportster engine. The frame features a single downtube. monoshock swingarm. oil runs through the downtube. 28 degree of neck rake. overall stretch is 3" over stock GSXR1000 specifications. to allow for the Buell/Sportster transmission. WHEELS & BRAKES PM / Performance Machine custom made wheels (gloss black and glass bead blasted accents)  Front | 18 x 3. 5 / Metzeler 120 x 18 Rear | 18 x 8. 5 / Metzeler 240 x 18  PM / Performance Machine matched brake disks  PM / Performance Machine radial brake caliper Exile Cycles Sprotor (sprocket brake) Stainless steel braided brake lines   HAND & FOOT CONTROLS Storz / Todd's Cycle modified rear sets (gloss black and glass bead blasted finish) PM / Performance Machine  Contour hand controls (gloss black and glass bead blasted finish) Storz Perfomance foot pegs Custom made aluminum clip-ons Todd's Cycle grips   (gloss black and glass bead blasted finish) BODY. PAINT & FINISHES Frame is  a one-off custom powdercoat by Specialized Coatings and is a champagne metallic. Hand formed aluminum bodywork; gas tank. oil tank. tail section front fender and rear fender are hand formed aluminum and black anodized) Hand formed aluminum oil tank (sits behind frame neck) is a top fill (see cap in front of gas tank) is black anodized with AN fittings. braided hose and runs through the downtube. Paintwork by Color Zone Designs (http://www. colorzonedesigns. com) Anodizing by Sport Chrome (http://www. sportchrome. com) Frame powder coat and ceramic exhaust coating by Specialized Coatings (http://specializedcoating. com/) 2013 powder coat by Seattle Powder Coat (http://seattlepowdercoat. com) ELECTRICAL & LIGHTING Todd's Cycle "gear" headlight Custom LED brake light / running lights Todd's Cycle "switch" DYNA 2000i ignition

SHIPPING Shipping is the sole responsibility of the winning bidder. however I will do my best to assist with shipping where applicable. EMAIL me with any questions. Click here WWW. BULLCAFE. WEEBLY. COM for more photos. details. build photos. etc. All details are to the best of my knowledge and do not offer any warranty or guarantee as this motorcycle is sold AS-IS.

On Nov-09-14 at 18:54:25 PST. seller added the following information:

On Nov-09-14 at 18:58:30 PST. seller added the following information:

On Nov-10-14 at 18:24:30 PST. seller added the following information:

based on email questions. here are a couple others things to mention.

Wheels were custom ordered made at Performance Machine (PM) to Todd's specification for this build (paperwork included)Rocker boxes are Evo big twin. gloss black with flat black center section (powdercoat). The Bassani custom made under seat exhaust does not heat up the aluminum tail section. I custom built aluminum heat diffusers and wrapped everything with heat resistant Dynamat. the fuel petcock is a high end Golan setup. the brand new Mikuni HSR42 has a Todd's Cycle chock relocation kit (black anodized)the paint scheme is gloss black base with matte black panels. and pinstripting that matches the silver color of the bead blasted aluminum. all done by Colorzone Designs in So Cal. The Exile Sprotor is a "sprocket brake" and works great. For more information on Exile Sprotors. click here. http://www. exilecycles. com/index. php?section=34

If you have other questions. want more pics or details. let me know.

Also published at eBay.com